Differences

This shows you the differences between two versions of the page.

--- sw_release [2018/05/20 19:41] – arzaman
+++ sw_release [2025/04/01 09:44] (current) – external edit 127.0.0.1
@@ Line 64: / Line 64: @@
+==== SPC1000-biab-v1.3-008.bin====
+Date	27 Oct 2018
+  * replaced ThingSpeak API integration with MQTT connectivity
+  * added 4126 beta value for NTC sensors
+  * fixed support for newer versions of the ESP8266 firmware
+  * added averaging of multiple temperature readings with NTC probes to minimize impact of noise
+  * fixed a bug in the recipe hop addition menu,
+  * added temperature unit (C/F) and run mode type (manual/auto) in dynamic data sent via MQTT
+  * added run-time detection of hardware version (classic vs stackable SmartPID)
+  * added “Sound Alarms” configuration menu to selectively activate the buzzer
+  * added dynamic management of “set point reached” to reflect run-time changes to set point
+  * added run mode dynamic status persistence (pause/resume, crash recovery)
+  * added PWM regulation of SSR output in status mode
+  * added PUMP = off e Mash Probe Position = external consistency check
+  * Changed hysteresis logic in on/off mode so that controller output is deactivated when temperature reaches set point and activated when temperature reaches [set point - hysteresis]
+  * Fixed DS18B20 temperature reading for values below 0 °C
+  * Added auto-resume configuration option for automatically resuming interrupted process after power-up
+  * Added "power restored" MQTT event when an interrupted process is detected at power-up
+  * Added "resume" MQTT event when an interrupted process is resumed
+  * Added "resume" MQTT command to remotely resume an interrupted process
+  * Fixed process timestamp initialization after resumption of an interrupted process
+  * Added watchdog protection
+  * Added logging to SD card [cube version only]
+  * Fixed issue where controller freezes after resuming an interrupted process
+  * Fixed issue where mash and HLT output drivers are wrongly enabled when resuming a process that had been interrupted when in paused mode
+  * Fixed sending of MQTT dynamic data when process is paused
+  * Added MQTT “stop” event when exiting from status mode
+  * For each mash step, added MQTT “start” event when reaching set point, and “end” event when timer expires
+  * Fixed resuming of process after power loss when process has been running for a long time
+  * Added on-screen indication of actual hardware, i.e. "SPC1000 V6.1" or "SPC1000 cube V2.3"
+  * Fixed “set point reached” notification in manual mode when mash set point is changed via MQTT commands
+{{ ::spc1000-biab-v1.3-008.bin.zip |}}
+==== SPC1000-biab-v1.3-009.bin====
+Date	03 Dec 2018
+  * Removed operation of PA13 pin as digital output, to fix current consumption issue causing a voltage drop that interferes with NTC probe measurements
+  * Fixed bug where software may freeze when probe configuration is changed from DS18B20 to NTC
+{{ ::spc1000-biab-v1.3-009.bin.zip |}}
+==== SPC1000-biab-v1.3-010.bin====
+Date	19 jan 2019
+  * Added Brewfather integration components
+  * Added MQTT process start command
+  * Added MQTT pump on/off command
+  * Added pump cycle pause/resume in auto mode
+  * Added pump status in MQTT dynamic data
+  * Added possibility to skip step mash in BIAB recipe
+  * Fixed bug where mash and HLT heater outputs are enabled unconditionally upon resuming a paused process in automatic run mode
+  * Added PWM control of mash channel during boil phase via MQTT commands
+  * Added pump status icons
+**NOTE** this SW release is mandatory for [[https://web.brewfather.app|External Link]] INTEGRATION
+{{ :spc1000-biab-v1.3-010.bin.zip |}}
 ===== Smart Thermostat =====
@@ Line 160: / Line 224: @@
 {{ :spc1000-base-wifi-v0.5-011.bin.zip |}}
+==== SPC1000-base-wifi-v0.5-013.bin ====
+date	27 Oct 2018
+  * Fixed DS18B20 temperature reading for values below 0 °C
+  * Added auto-resume configuration option for automatically resuming interrupted process after power-up
+  * Added "power restored" MQTT event when an interrupted process is detected at power-up
+  * Added "resume" MQTT event when an interrupted process is resumed
+  * Added "resume" MQTT command to remotely resume an interrupted process
+  * Fixed process timestamp initialization after resumption of an interrupted process
+  * Added watchdog protection
+  * Added logging to SD card [cube version only]
+  * Added delayed start feature
+  * Fixed issue where output drivers are wrongly enabled when resuming a process that had been interrupted when in paused mode
+  * Fixed sending of MQTT dynamic data when process is paused
+  * Fixed resuming of process after power loss when process has been running for a long time
+  * Added on-screen indication of actual hardware, i.e. "SPC1000 V6.1" or "SPC1000 cube V2.3"
+  * Fixed “set point reached” notification when set point is changed via MQTT commands
+{{ ::spc1000-base-wifi-v0.5-013.bin.zip |}}
+==== SPC1000-base-wifi-v0.5-014.bin ====
+date	03 Dec 2018
+  * Added Brewfather integration components
+  * Removed operation of PA13 pin as digital output, to fix current consumption issue causing a voltage drop that interferes with NTC probe measurements
+  * Fixed bug where software may freeze when probe configuration is changed from DS18B20 to NTC
+**NOTE** this SW release is mandatory for [[https://web.brewfather.app|External Link]] INTEGRATION
+{{ ::spc1000-base-wifi-v0.5-014.bin.zip |}}
@@ Line 180: / Line 279: @@
 {{ :spc1000-bbq-v3.0-012.bin.zip |}}
+==== SPC1000-bbq-v3.0-014.bin ====
+date 20 Oct  2018
+  * Made servo pulse length setting configurable from 900 to 2100 microseconds
+  * Added support for resuming interrupted process after power-up
+  * Added auto-resume configuration option for automatically resuming interrupted process after power-up
+  * Added watchdog protection
+  * Added on-screen indication of actual hardware, i.e. "SPC1000 V6.1" or "SPC1000 cube V2.3"
+{{ ::spc1000-bbq-v3.0-014.bin.zip |}}